Tach-Y Tach

$35.00

Out of stock

Categories: ,

Description

Tach-y Tach Signal Generator Tach Calibration Tool

I’ve been working on this project for about three years. There are many variables I had to conquer. First, purchasing a professional oscilloscope was not in the budget. It had to be simple enough to use that one would not need to read a 400 page manual. It needed to be extremely inexpensive so guys would put one in their tool box just because they might use it someday. It had to be easy to assemble as there are not enough hours in the day as it is. A 3D Printed housing was a must. It needed to be small and cheap to ship.

Well, through a series of friends, many hours at TechShop and in my shop, I have come up with THE answer!

Attach the Tach-y Tach to the tach BEFORE you remove the needle. The generator is only between 8,500 to 9,500 rpm. Each one, and each tach, will read slightly different. Make a note of what you tach reads with a new 9 volt battery. The generator must have the battery removed when not in use as it only has about an hour of run time. Tach does not respond? Install a new battery.

Remove the needle with two teaspoons pivoting on the screws holding the face on.

It will come with a small vial of Kano Kroil. Use VERY sparingly only one to two drops in the tach hole the needle goes into.

To install the needle, attach the Tach-y Tach then insert the needle at the rpm you made a note of. Do not insert too far.

Connect/disconnect the Tach-y Tach and watch the needle move. It should be smooth. If not, adjust it up/down in the tach until it is.

WARNING: ELS Products MAY CONTAIN, or be Made With, Patented Parts, Tools, Components and/or Apparati. Manufacturing Facility DOES Contain Nuts.

 
 
 
 

Additional information

Weight .5 lbs
Cart
Genuine Hella 80/100 H4 Headlight BulbGenuine Hella 80/100 H4 Headlight Bulb
$28.00
×
92049-1496 Fork Seal92049-1496 Fork Seal
$67.50
×
EMERGENCY!! 10mm SocketEMERGENCY!! 10mm Socket
$140.00
×
Yoshimura-Spec CamshaftsYoshimura-Spec Camshafts
$5,780.00
×
Friggin' KWICK Valve Spring ToolFriggin' KWICK Valve Spring Tool
$50.00
×
Tensioner Tamer™ Alternator/Starter Chain Tensioner FixTensioner Tamer™ Alternator/Starter Chain Tensioner Fix
$180.00
×
Titanium LadyBird "Loudener" Exhaust BracketTitanium LadyBird "Loudener" Exhaust Bracket
$35.00
×
11061-1155  Pulser Ignition Cover Gasket11061-1155 Pulser Ignition Cover Gasket
$16.74
×
Shorai LFX14A2-BS12 Battery BracketShorai LFX14A2-BS12 Battery Bracket
$90.00
×
Brake Light Banjo Bolt SwitchBrake Light Banjo Bolt Switch
$14.00
×
Titanium Case GuardTitanium Case Guard
$90.00
×
Mo'Flo! and 2.5 Battery TrayMo'Flo! and 2.5 Battery Tray
$135.00
×
PlaceholderZRX Front Brake Caliper Kit
$58.59
×
K&N Pod Side Cover Bracket SetK&N Pod Side Cover Bracket Set
$80.00
×
Öhlins and 1997-2003 ZRX Fork Cap WrenchÖhlins and 1997-2003 ZRX Fork Cap Wrench
$30.00
×
PlaceholderKWICK's Ti Petcock Seal Set
$9.00
×
17mm "sorta" 99-2003 ZRX Fork Preload Socket17mm "sorta" 99-2003 ZRX Fork Preload Socket
$12.00
×
11061-1154 Clutch Cover Gasket11061-1154 Clutch Cover Gasket
$13.71
×
CVK40 K&N Pod AdaptersCVK40 K&N Pod Adapters
$240.00
×
16099-003  Oil Filter16099-003 Oil Filter
$12.17
×
LED Turnsignal RelayLED Turnsignal Relay
$20.00
×
KWICK ThrottleKWICK Throttle
$88.00
×
ZRX Brake Bleeder ToolZRX Brake Bleeder Tool
$22.50
×
Fork-Off! Bug and Stone ProtectorsFork-Off! Bug and Stone Protectors
$50.00
×
1997-2003 ZRX Fork Preload and Cartridge Bottom Wrench1997-2003 ZRX Fork Preload and Cartridge Bottom Wrench
$30.00
×
PlaceholderZRX Rear Brake Caliper Kit
$25.17
×
KWICK's Rad Radiator Bracket SetKWICK's Rad Radiator Bracket Set
$45.00
×
15410-19E10 Suzuki Fuel Filter15410-19E10 Suzuki Fuel Filter
$22.07
×